Liebherr Freezer 7082 308 00 User Manual

Operating instructions  
GB  
for NoFrost freezer with electronic controls  
7082 308-00  
GN...3  
3805  
 
Congratulations on your purchase. In choosing  
this appliance you have opted for all the benefits of  
state-of-the-art refrigeration technology, guarantee-  
ing you top quality, a long life span and excellent  
reliability.  
The features on your appliance have been designed  
to ensure maximum convenience - day in, day out.  
This appliance has been manufactured with recycla-  
ble materials using an environmentally friendly proc-  
ess, so together you and we are making an active  
contribution to the preservation of our environment.  
To get to know all the benefits of your new ap-  
pliance, please read the information contained in  
these operating instructions carefully.  
Safety regulations  
W The appliance is designed to freeze and store food  
and to make ice. It is designed as a household ap-  
§
pliance. We cannot guarantee that the appliance will work  
properly if it is used for another purpose.  
W The appliance is set to operate within specific ambient  
temperature limits according to its climate rating. These  
temperature limits should not be exceeded. The correct  
climate rating for your appliance is indicated on the type  
plate. This is explained as follows:  
GB  
Climate rating  
Set for ambient temperatures  
SN, N  
ST  
T
up to +32°C  
up to +38°C  
up to +43°C  
- The appliance will function properly in ambient tempera-  
tures of down to +5°C.  
- The refrigerant circuit has been tested for leaks.  
- The appliance complies with current safety regulations  
and EC directives 73/23/EEC and 89/336/EEC.  
We wish you much pleasure with your new appli-  
ance.  
Keep these operating instructions in a safe place and  
pass them on to the next owner, where applicable.  
The operating instructions apply to several models.  
Differences may therefore occur.  
Notes on energy saving  
Contents  
Page  
W Ensure that there is adequate space around the appliance  
for ventilation and air extraction.  
Operating instructions  
W Avoid keeping the door open for too long.  
W Store food logically. Do not exceed the storage period  
specified.  
W Keep all food properly packed and covered so as to  
avoid its frosting up on the outside.  
W Always allow hot food to cool to room temperature before  
placing in the appliance.  
W Defrost frozen food in the refrigerator.  
W Keep the appliance door shut in the event of a break-  
down. This will delay the cold loss and will help to main-  
tain the quality of the frozen food for longer.  
The appliance at a glance.................................. 12  
Contents, Safety regulations.............................. 13  
Energy savings................................................... 13  
Safety instructions and warnings............................ 14  
Disposal notes ................................................... 14  
Setting up........................................................... 14  
Operation and control elements.............................. 15  
Connecting to the mains.................................... 15  
Switching the appliance on and off ................... 15  
Setting the temperature ..................................... 15  
Temperature setting display............................... 15  
Audible warning signal, red visual  
warning light....................................................... 15  
SuperFrost............................................................... 16  
Notes on freezing and storage........................... 16  
Equipment............................................................... 17  
Information system ............................................ 17  
Freezer tray ........................................................ 17  
Cold-storage accumulators ............................... 17  
Making ice-cubes .............................................. 17  
VarioSpace*........................................................ 17  
Cleaning .................................................................. 18  
Troubleshooting....................................................... 18  
Customer service and type plate....................... 19  
The insulation plate for running freezer at part  
capacity  
is available as an accessory from  
your dealer.  
If you do not store much frozen food  
2
4
6
-
-
6
8
-12  
7
in your freezer you can use the insula-  
tion plate to cut your freezer's energy  
consumption by up to half.  
- You can "switch off" any number  
of drawers up to 5 (depending on  
model). At least 2 drawers are  
required for the refrigeration unit to  
work.  
2
4
6
-
-
6
8
-12  
6
2
4
6
-
-
6
8
-12  
4
2
4
6
-
-
6
8
-12  
3
2
4
6
-
-
6
8
-12  
2
2
4
6
-
-
6
8
-12  
1
For more information see the  
instruction manual of the insulation  
plate.  
Instructions for installation and modification  
Dimensions ........................................................ 20  
Changing over door hinges...........................20-21  
*
GN..3  
13  
 
Safety instructions and warnings  
Disposal notes  
Safety during use  
The packaging is designed to protect the appliance  
and individual components during transport and is  
made of recyclable materials.  
W Do not store explosives or sprays using combus-  
tible propellants such as butane, propane, pentane,  
etc. in the appliance. Electrical components might cause  
leaking gas to ignite. You can identify such sprays by the  
printed contents or a flame symbol.  
- Corrugated board/board  
- Moulded polystyrene (foamed, CFC-free polystyrene)  
- Polythene bags and sheets  
W Only store high-percentage alcohol in tightly sealed, up-  
right containers.  
- Polypropylene straps  
W Keep packaging materials away from children - poly-  
thene sheets and bags can suffocate!  
W Please return the packaging material to your nearest of-  
ficial collection point so that the various materials can be  
reused or recycled as far as possible.  
W Do not allow naked flames or ignition sources to enter the  
appliance.  
W Do not use electrical appliances inside the appliance (e.g.  
steam cleaners, heaters, ice makers, etc.).  
W Do not stand on the plinth, drawers or doors or use them  
to support anything else.  
Your old appliance:  
W This appliance is not intended for use by persons (includ-  
ing children) with reduced physical, sensory or mental  
capabilities or lack of experience and knowledge unless  
they have been given initial supervision or instruction  
concerning use of the appliance by a person responsible  
for their safety. Children should be supervised to ensure  
that they do not play with the appliance.  
W Avoid prolonged skin contact with cold surfaces or  
chilled/frozen food. This could cause pain, numbness and  
frostbite. In the case of prolonged skin contact, protective  
measures should be taken, e.g. gloves should be worn.  
W Do not eat ice-cream, particularly ice lollies or ice-cubes,  
immediately after taking them from the freezer compart-  
ment as there is a risk of "burning" because of the very  
cold temperatures.  
This contains some reusable materials and should be  
disposed of properly - not simply with unsorted house-  
hold refuse.  
W Disable discarded appliances immediately by  
removing the plug and cutting through the connection  
cable.  
W Remove the spring-action or bolt catch from the appli-  
ance so that playing children cannot become trapped  
inside and suffocate.  
W Make sure that the refrigerant circuit of an appliance that  
is no longer needed is not damaged before it is collected  
or handed in at a municipal collection point so as to  
ensure that the refrigerant or oil does not escape into the  
environment.  
- Exact details of the refrigerant used can be found on the  
type plate. The heat insulator is PU with Pentane.  
- Information on collection dates or collection points can  
be obtained from the waste disposal authorities or your  
local council.  
W Do not consume food which has been stored for too long,  
as it could cause food poisoning.  
Setting up  
W When setting up/fitting ensure that the refrigerant circuit  
pipes are not damaged.  
Technical safety  
W Once in position, use the 10 spanner provided to adjust  
the feet so that the appliance is level and does not  
wobble.  
W Avoid positioning in direct sunlight or next to an  
oven, radiator or similar, in damp locations or near  
spraying water.  
W To prevent injury or damage to the unit, the ap-  
pliance should only be transported wrapped and  
set up by two people.  
W The refrigerant R 600a is environmentally friendly but  
flammable.  
W Do not damage the refrigerant circuit pipes. Splashes of  
refrigerant can harm your eyes or ignite.  
The basement is an ideal site for installation.  
W Standard EN 378 specifies that the room in which you  
install your appliance must have a volume of 1 m3 per 8 g  
of R 600a refrigerant used in the appliance, so as to avoid  
the formation of inflammable gas/air mixtures in the room  
where the appliance is located in the event of a leak in  
the refrigerant circuit. The quantity of refrigerant used in  
your appliance is indicated on the type plate on the inside  
of the appliance.  
W The ventilation grilles should not be obstructed.  
Always ensure that there is good ventilation and  
that the outward flowing air is able to escape.  
Please note the appendix concerning installation  
instructions.  
W If refrigerant escapes, remove all naked flames or sources  
of ignition in the vicinity of the leak, disconnect the ap-  
pliance from the mains and ventilate the area well.  
W In the event that the appliance is damaged, contact the  
supplier immediately before connecting to the mains.  
W To guarantee safe operation, ensure that the appliance  
is set up and connected as described in these operating  
instructions.  
W Disconnect the appliance from the mains if any fault oc-  
curs. Pull out the plug (not by pulling on the mains cable)  
or switch off or remove the fuse.  
W
Any repairs and work on the appliance should only be car-  
ried out by the customer service department, as unauthor- W Do not place heat-emitting appliances, e.g. micro-  
ised work could prove highly dangerous for the user. The  
same applies to changing the mains power cable.  
wave oven, toaster, etc., on top of the refrigerator or  
freezer.  
W Remove all transportation safety components.  
GN..3  
14  
 
Operation and control elements  
Setting the temperature  
fig. A1  
GB  
W Turn the temperature control with a coin until the desired  
temperature is indicated in the display. The slot posi-  
tions mean:  
Setting 1  
= highest temperature,  
lowest cooling setting  
Setting "max." = lowest temperature,  
highest cooling setting  
W Recommended temperature setting: -18°C.  
You are advised to clean the appliance before switching it  
on for the first time (see "Cleaning").  
Switch on the appliance approx. 4 hours before loading it  
with frozen food for the first time.  
Temperature setting display  
fig. A1/3  
- When the temperature display is illuminated, this indi-  
cates that the appliance is running.  
- The five blocks in the display each relate to a different  
temperature range. They indicate the freezer tempera-  
ture setting you have selected.  
- Within the temperature / setting range, e.g. when the  
display reads -15 °C to -18 °C, or between two set-  
tings*, the temperature can be set slightly colder. If  
required, slowly turn the temperature control 1further -  
the light displaying the temperature range, e.g. -18 °C,  
flashes for a short time. This confirms the higher setting  
within the small temperature range.  
Connecting to the mains  
Power supply (AC) and voltage  
at the operating point must comply with the details on  
the type plate, which is located inside the appliance on  
the left, fig. A.  
W Connect the appliance with a properly earthed fused  
plug and socket only.  
W The socket must be fused with a 10 A fuse or higher, it  
must be away from the rear of the appliance and must be  
easily accessible.  
W Do not  
- connect to stand-alone inverters,  
- operate with so-called energy-saving plugs - this can  
damage the electronic system,  
- connect to the supply with other equipment using an  
extension cable - risk of overheating.  
W When removing the mains cable from the back of the ap-  
pliance, remove the cable holder as well so as to avoid  
vibration noise.  
Audible warning signal,  
red visual warning light  
The wires in the mains lead are coloured in accordance with  
the following code: green/yellow = earth, blue = neutral,  
brown = live.  
fig. A1  
The audible warning signal and the red visual warning light  
are designed to help you to protect your frozen food and to  
save energy.  
Warning! This appliance must be earthed.  
Non-rewireable plugs BS 1363  
If this machine or appliance is fitted with a non-rewireable  
plug, the following information applies: If the socket outlets  
are not suitable for the plug supplied with this product, it  
must be cut off and an appropriate plug fitted. The plug cut  
from the flexible cord should be disposed of and on no ac-  
count be inserted into a 13 A socket elsewhere in the house  
(electric shock hazard).  
The fuse cover must be re-fitted when changing the fuse,  
and if the fuse cover is lost the plug must not be used until  
a suitable replacement is obtained. The colour of the cor-  
rect replacement cover is that of the coloured insert in the  
base of the plug, or the colour that is embossed in words  
on the base of the plug (as applicable to the design of the  
plug fitted). The correct rating of the replacement fuses that  
are ASTA approved to BS 1362 should be fitted. Replace-  
ment fuse covers may be purchased from your local elec-  
trical suppliers, electricity showroom or approved service  
agent.  
W The audible warning device is switched off by press-  
ing the audible warning on/off button 4.  
- It switches off automatically as soon as the temperature  
is low enough.  
- It always sounds if the freezer temperature is not low  
enough (dependent on the temperature setting).  
- The red visual warning light will flash simultaneously.  
This can be caused by:  
- warm, fresh food being placed in the freezer,  
- too much warm air from the outside entering when re-  
arranging or removing frozen food. These temperature  
fluctuations will not affect the quality of the frozen food.  
- When the audible warning on/off button is pressed, the  
visual warning light will stop flashing and will light up  
continuously. It will only go out once the alarm status  
stops and the temperature inside the freezer is low  
enough. The audible warning signal will then switch  
back to standby automatically.  
Switching the appliance on and off  
fig. A1  
W To switch on: Turn the temperature control 1with a coin  
so that the slot is pointing to setting 2.  
W If the SuperFrost button flashes at the same time as  
one of the lights on the temperature display, this means  
that your appliance has a fault. Contact your customer  
service department and tell them that this visual warning  
is active, so that they can arrange for your appliance to  
be serviced accurately and quickly.  
- The red visual warning light will be on until the freezer  
has reached a sufficiently low temperature, then it goes  
out. See "Audible warning signal, red visual warning  
light" for more information.  
- A green light on the temperature display will light up and  
indicate that the appliance is in normal mode.  
W To switch off: Set the temperature control to "0".  
- The temperature display and all buttons will go out.  
GN..3  
* Depending on model and options  
15  
 
SuperFrost, notes on freezing and storage  
W Do not freeze bottles and cans which contain carbonated  
SuperFrost  
drinks as they might burst. Drinks can be cooled down  
quickly, but take the bottles out of the freezer compart-  
ment after an hour at the most.  
Fig. A1/2. Fresh food should be frozen to the core as  
rapidly as possible. Frozen food can also be given a cold  
boost. This is provided by the SuperFrost facility and en-  
sures that the nutritional value, appearance and flavour of  
the food remain intact.  
W Storage: Each drawer and cooling plate can take up to  
25 kg frozen food.  
W If you want to use the maximum net capacity, you can re-  
move the drawers and store items directly on the shelves.  
- Always leave the bottom drawer in the appliance.  
W Removing drawers: Pull forward  
until the drawer stops and lift out.  
- If you have removed the drawers, do  
not cover the fan slits at the back,  
otherwise the freezer will not work  
properly.  
W Always store identical food items to-  
gether to avoid the door being open  
for unnecessarily long periods and to  
save energy.  
W The maximum amount of food which can be frozen in  
24 hours is shown on the type plate ("Freezing capacity  
... kg/24h"). This amount varies according to the model  
and climate rating.  
Freezing with SuperFrost  
W Press the SuperFrost button 2briefly until it lights  
up; the lowest set temperature on the temperature  
display will also light up.  
The freezer temperature will decrease and the appliance  
will switch to the lowest temperature.  
W For small amounts of frozen food, it is normally suffi-  
cient to switch on SuperFrost 6 hours beforehand. For  
the maximum amount (see freezing capacity on the type  
plate) you will need to switch it on 24 hours beforehand.  
W Then place the fresh food inside the freezer, preferably in  
the top drawers.  
W Do not exceed storage times given.  
W Thawing: Only take out as much food as is immediately  
required for thawing. Cook food which has been thawed  
as quickly as possible.  
Frozen food can be thawed in the following ways:  
- in a conventional or fan oven  
- in a microwave oven  
- at room temperature  
- in the refrigerator: the cold given off by the frozen food is  
used for cooling the other food.  
- Flat portions of meat or fish can be cooked when partially  
thawed.  
- Vegetables can be cooked from frozen (in half the normal  
time).  
If freezing the maximum quantity of food, do not use the  
drawers; instead, place the wrapped food directly on the  
cooling plates. Once the food is frozen you can load it  
into the drawers.  
- The SuperFrost function switches off automatically after  
about 65 hours. The freezing process is now finished;  
the SuperFrost button has gone out, the set tempera-  
ture is displayed again and the appliance has switched  
back to energy-saving normal mode.  
You should not switch on the SuperFrost function:  
- when placing frozen food in the freezer;  
- when freezing up to approx. 2 kg fresh food daily.  
Notes on freezing and storage  
W Items suitable for freezing: meat, game, poultry, fresh  
fish, vegetables, fruit, dairy products, bread, baked  
goods, pre-cooked meals.  
Not suitable: lettuce, radishes, grapes, whole apples and  
pears, fatty meat.  
W Pack frozen food in standard freezer bags or reusable  
plastic, metal or aluminium containers.  
W Do not allow fresh food which is to be frozen to come into  
contact with food already frozen. Always keep packs dry  
in order to avoid them sticking together.  
W Always write the date and contents on the pack and do  
not exceed the stated storage time for the food. This  
prevents any risk of quality impairment.  
W Pack food which you are freezing yourself in quantities  
appropriate to your household. To ensure that the food  
freezes right through quickly, the following quantities  
should not be exceeded per package:  
- fruit, vegetables: up to 1 kg;  
- meat: up to 2.5 kg.  
W Blanch vegetables after washing and cutting them. (Add  
to boiling water for 2-3 minutes, remove and quickly  
cool down in cold water. If you blanch with a steamer or  
microwave oven, please observe the relevant operating  
instructions.)  
W Do not salt or season fresh food or blanched vegetables  
before freezing. Only lightly salt and season other food.  
Some spices can alter their flavour intensity.  
GN..3  
16  
 
Equipment  
pre-cooked  
meals  
sausages  
bread  
2 - 6  
4 - 8  
6 -12  
2
Information system*  
Use frozen food within the recommended period.  
The numbers between the symbols indicate the storage  
period in months for different kinds of frozen foods.  
Storage times given are guide times for food frozen at  
home. Whether or not the lower or upper value is applicable  
depends on the food quality and how it was processed prior  
to freezing. The lower values always apply to food with a  
high fat content.  
ice-cream  
GB  
fish  
mushrooms  
game  
pork  
vegetables  
fruit  
poultry  
beef/veal  
G
Freezer tray*  
This is used for gently freezing berries, herbs, vegetables  
and other small items and prevents them from sticking to-  
gether. Items being frozen will largely retain their shape, and  
it will be easier to remove exactly the right quantity later on.  
W Spread the items out loosely on the tray, fig. H.  
W Freeze for 10 to 12 hours, then transfer to a freezer bag  
or container and put in a drawer.  
W To defrost, spread the frozen items out loosely.  
6
8
-
-
2
4
H
Cold-storage accumulators*  
These prevent the temperature in the freezer from rising too  
quickly in the event of a power failure, thus preserving the  
quality of the food.  
W To save space, you can freeze and store the cold-  
storage accumulators in the freezer tray, fig. I.  
- To ensure maximum storage time in the event of a power  
failure, place the frozen cold-storage accumulators in the  
top freezer drawer on top of the food.  
6
8
-
-
2
4
I
Making ice-cubes*  
W Fill the ice-cube tray with water.  
W Place the ice-cube tray in the appliance and leave it to  
freeze.  
W The ice-cubes can be removed from the tray by twisting  
or by holding upside down for a short time under running  
water.  
J
VarioSpace*  
- You can create a double-height space for big items of  
frozen food by removing a drawer and a shelf. This ena-  
bles you to freeze such things as poultry or big pieces of  
meat without having to cut them up first, so they can be  
served "whole" afterwards, and to store other large items  
such as big gateaux or packs of ice.  
2
-1  
-
12  
6
6
5
5
6
8
-
-
2
4
6
2
-1  
4
- Removing the drawer, fig. K1: Pull forward until the  
-
-
6
2
4
6
8
drawer stops and lift out.  
2
-1  
K1  
K2  
3
- Removing the shelf, fig. K2: Lift up at the front and pull  
out.  
- To insert: proceed in reverse order; simply push shelf in  
as far as it will go.  
-
-
6
8
2
4
6
2
-1  
2
2
1
6
8
2
4
6
-
-
-
12  
1
K3  
GN..3  
* Depending on model and options  
17  
 
Cleaning  
Troubleshooting  
Your appliance is designed and manufactured for a long life  
span and reliable operation.  
Notes on defrosting  
The NoFrost system automatically defrosts the appliance.  
Any moisture arising collects on the evaporator and freezes,  
and is periodically defrosted and evaporated.  
The automatic defrosting system keeps the freezer frost-  
free and eliminates the time and effort spent on defrosting  
manually.  
If a malfunction nonetheless occurs during operation, check  
whether it is due to an operating error. Please note that  
even during the warranty period the resultant servicing costs  
in this case will have to be borne by the owner.  
You may be able to rectify the following faults by checking  
the possible causes yourself  
Malfunction  
- Possible cause and remedy  
Cleaning  
______________________________________________________  
W Always disable the appliance for cleaning. Dis-  
connect from the mains or unscrew or switch  
off the fuse.  
Appliance does not work  
- Is the appliance switched on properly?  
- Is the mains plug properly inserted in the socket?  
W
W
W
Clean the outer walls, inside and equipment by hand with  
lukewarm water and a little detergent. Because of the risk - Is the socket fuse intact?  
of injury and damage to the appliance, steam cleaning  
equipment should not be used.  
We recommend using a soft cloth and an all-purpose  
cleaner with a neutral pH value. Only use food compati-  
ble cleaning and care agents on the inside of the appli-  
ance.  
Loud running noise  
- Is the appliance standing firmly on the floor, or does the  
compressor cause nearby items of furniture or objects to  
vibrate?  
If necessary, move the appliance slightly, align by adjust-  
ing the adjustable feet, or move bottles and containers  
apart.  
Use a commercially available stainless-steel cleaning  
agent for stainless-steel appliances*.  
- Burbling noises are normal. These are caused by the  
refrigerant flowing round the refrigerant circuit.  
A short clicking sound: This will be heard whenever the  
refrigeration unit (the motor) switches on or off automati-  
cally.  
Motor noise: This will be slightly louder for a brief period  
when the refrigeration unit switches on.  
The audible warning signal sounds, the red audible  
warning on/off button is lit, the temperature is not cold  
enough  
- Have you put too much fresh food into the freezer without  
activating SuperFrost? (See "SuperFrost")  
- Does the door close properly?  
- Is the appliance sufficiently well ventilated?  
Clear ventilation grilles if necessary.  
- In order to achieve best possible protection, apply a stain-  
less-steel care agent uniformly in grinding direction after  
cleaning. Points which are darker at the start and a more  
intensive coloration of the stainless-steel surface are nor-  
mal.  
- Do not use abrasive sponges or scourers, do not use con-  
centrated cleaning agents and never use cleaning agents  
containing sand, chloride or acid or chemical solvents, as  
these would damage the surfaces and could cause corro-  
sion.  
W Ensure that no cleaning water is allowed to penetrate into  
the electrical components or ventilation grilles.  
Dry the appliance.  
- Do not damage or remove the type plate on the inside of  
the appliance as this is important for customer service.  
W The dust should be removed from the  
- Is the ambient temperature too hot? (See "Safety regula-  
tions")  
refrigeration unit and heat ex-  
changer - metal grid at the back of  
the appliance - once a year. Dust  
deposits increase energy consump-  
- Has the appliance been opened too often or left open too  
long?  
- If applicable, wait until the appliance reaches the required  
temperature itself.  
tion.  
The outside of the appliance may feel warm in places  
- That is quite normal. The heat from the cooling circuit is  
used to avoid the formation of condensate.  
W Ensure that none of the wires or  
other components are dislodged,  
bent or damaged.  
W Then connect/switch on the appliance, switch on Super-  
Frost and start to insert the food to be frozen as the  
temperature drops.  
If the appliance is to be left out of operation for any length  
of time, empty it, disconnect from the mains, clean as  
described above and leave the door open in order to avoid  
unpleasant smells.  
GN..3  
* Depending on model and options  
18  
 
Troubleshooting  
Customer service and type plate  
If none of the above causes apply and you cannot  
rectify the fault yourself, or if several lights are flash-  
ing simultaneously, please contact your nearest customer  
service department (see enclosed list for addresses). State  
the:  
GB  
type designation 1,  
service number 2and  
appliance number 3  
as given on the type plate and specify which lights are  
flashing, so as to ensure rapid, accurate servicing. The  
type plate is located inside the freezer compartment on the  
left-hand side.  
Leave the appliance shut until the customer service engin-  
eer arrives so as to prevent any further cold loss.  
GN..3  
19  
 
Instructions for installation and modification  
W With the door open, insert the cover 2in the plinth panel  
Dimensions  
at the front and click into place at the back.  
W Transfer* door handle bland plugs bm: With the door  
open, carefully lift out the pressure plates* bn at the front  
and slide away; unscrew handle.  
The external dimensions of the appliance can be seen on  
fig. S and in the table below.  
Gross capacity  
of appliance [l]  
(see type plate)  
External dimensions [mm]  
A
B
C
D
E
F
Re-assemble in reverse order: replace the pressure plates  
and click into position.  
162  
200  
238  
276  
(18..)  
1250 600 631 614 644 1179  
1447 600 631 614 644 1179  
1644 600 631 614 644 1179  
1841 600 631 614 644 1179  
(21..)  
(25..)  
(28..)  
Insertion into row of kitchen units  
Fig. U. 600 mm appliances can be installed in a row of  
kitchen units. To adapt the height of the appliance to the  
surrounding furniture a top unit 1can be added.  
A gap of at least 50 mm depth must be provided behind and  
along the entire width of this unit so as to ensure sufficient  
ventilation. The area of ventilation underneath the ceiling  
should be at least 300 cm2. The greater the area the more  
economically the appliance will run.  
W When installing with standard kitchen units (max. depth  
580 mm) and decor panels of max. 2 mm thickness, the  
appliance can be set up right next to the kitchen unit.  
The door protrudes 34 mm from the side of the kitchen  
unit and 51 mm at the front. This enables it to be opened  
and closed without difficulty.  
188  
233  
279  
324  
(20..)  
(24..)  
(29..)  
(33..)  
1250 660 683 662 704 1287  
1447 660 683 662 704 1287  
1644 660 683 662 704 1287  
1841 660 683 662 704 1287  
Installation instructions  
- Do not install models without side-wall heating side-by-  
side with another refrigerator or freezer. This is important  
to prevent condensation and consequential damage from  
it.  
- Models with side-wall heating are designed for side-by-  
side installation; they are designed for combination with a  
refrigerator.  
Contact your dealer for more information.  
- Attachment instructions are supplied in the accessories  
bag of the appliance with side-wall heating.  
W When setting up the appliance next to a wall 4, a mini-  
mum distance of 36 mm must be provided on the hinge  
side between the appliance and the wall (for the handle  
when the door is open).  
Changing over door hinges  
The door hinges can be changed from one side to the other  
if required.  
1 top unit  
2 refrigerator/freezer  
3 kitchen unit side panel  
4 wall  
W With the door open, lever out plinth panel 1on the hinge  
side with a screwdriver and remove from front.  
- Lever out cover 2with a screwdriver.  
Close door.  
- Unscrew screw M5 3.  
W Pull hinge component 4with hinge pin 5out from un-  
derneath and remove.  
Notes on assembling decor panels  
with white appliances of width B = 600 mm and height  
A = 1841 mm:  
Decor panel and frames can be attached to the door of your  
appliance to match or contrast it to the existing kitchen  
colour scheme.  
The panels are available from your kitchen furniture supplier.  
The frames can be fitted later and are available from your  
dealer.  
If you wish to fit the decor panels yourself, you will need  
a drill or a rechargeable screwdriver to pre-drill the retain-  
ing holes. The door handles are to be replaced by the rigid  
handles included in the decor frame retrofit kit.  
For further instructions and dimensions see the installation  
instructions included in the retrofit kit.  
W Open door, lift out at bottom and remove; do not lose the  
spacer 6.  
W Transfer all hinge components onto the other side:  
- Lever out covers 8with a screwdriver at the front and  
remove at an angle from below. Remove hinge pin 7  
and insert on the opposite side. Use the hexagon  
socket on the open-ended spanner provided (spanner  
width 5). Fit covers 8again: insert at rear and click into  
place at front.  
- Bottom: Using a screwdriver, remove the spacer 9and  
replace on the other side.  
W Re-attach the door:  
- Remove plugs bofrom the door mounting points and  
replace on the other side.  
- Suspend door with spacer 6in hinge pin 7, close door.  
- Rotate hinge component 4by 180°, remove hinge pin 5,  
turn by 180° and replace. Mount both parts in the hinge  
bp: slide the pin into the door mounting through the  
hinge, tilt in the hinge component, slide up and attach  
with screw 3.  
W Align the door flush with the body of the appliance using  
the slot on the hinge bp, then tighten screw 3.  
W Attach the plinth panel 1and click into place by press-  
ing.  
GN..3  
20  
 
Instructions for installation and modification  
[mm]  
C
B
D
GB  
E
F
A
S
13  
8
7
SW5  
11 *  
8
10*  
12*  
Torx 15  
6
9
5
4
2
3
14  
9
1
14  
T1  
T
min.  
300 cm2  
[mm]  
1
2
_____________________________________________________  
All types and models are subject to continuous improve-  
ment and the manufacturer therefore reserves the right to  
make modifications in the shape, equipment and technolo-  
gy.  
3
4
min. 36  
U
GN..3  
21  
 

La Crosse Technology Portable Radio TX31U IT User Manual
Lenoxx Electronics Air Conditioner XC16 User Manual
Leviton Telephone 47609 TSV User Manual
Life Fitness Home Gym 93Xe User Manual
Lowrance electronic GPS Receiver GLOBALMAP 4800M User Manual
Magnavox CD Player MPC421 User Manual
Marshall electronic Car Video System V R65P HD User Manual
Mattel Drums 5281 User Manual
Maxtor Computer Drive D540X 4G User Manual
Mellerware Hot Beverage Maker 30J User Manual