Metra Electronics Automobile Accessories 99 8220 User Manual

INSTALLATION INSTRUCTIONS FOR PART 99-8220  
APPLICATIONS  
Toyota  
Tundra 2007-2011  
Sequoia 2008-2011  
99-8220  
KIT FEATURES  
• DIN Radio Provision with Pocket  
• ISO Mount Radio Provision with Pocket  
• Double DIN Radio Provision  
• Stacked ISO Mount Units Provision  
• 99-8220 - Scratch Resistant Matte Black  
• 99-8220HG - High Gloss Black  
• 99-8220CHG - High Gloss Charcoal (matches 2010-UP models)  
KIT COMPONENTS  
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets  
• E) Double DIN Trim Plate • F) Pocket  
C
D
A
E
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)  
Wire harness:  
• 70-1761 Toyota 87-up  
• TYTO-01 Toyota amp interface harness 03-up  
Antenna adapter:  
F
• Not required  
TOOLS REQUIRED:  
Small Flat Blade Screwdriver/ Panel Removal Tool  
• Phillips Screwdriver • Socket Set  
1-800-221-0932  
© COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORATION  
 
99-8220 DASH DISASSEMBLY  
TOYOTA TUNDRA (Console Shift) 2007-2011  
TOYOTA SEQUOIA 2008-2011  
A
Disconnect the negative battery ter-  
minal to prevent an accidental short  
circuit.  
1
2
3
Unclip and remove the top trim panel  
around cup holders. (Figure A)  
Remove (1) Phillips screw from shifter  
trim panel and remove panel.  
(Figure B)  
4
Unclip, unplug and remove the cli-  
mate control assembly. (Figure C)  
B
Continue dash disassembly.  
C
1
 
99-8220 DASH DISASSEMBLY  
TOYOTA TUNDRA (Console Shift) 2007-2011  
TOYOTA SEQUOIA 2008-2011  
5
6
Remove (4) 10 MM bolts securing the  
radio. (Figure D)  
Unclip the right side of the instrument  
panel trim and pull back the trim,then  
unclip,unplug and remove radio.  
(Figure E)  
Continue to kit assembly.  
2
 
99-8220 DASH DISASSEMBLY  
TOYOTA TUNDRA (Column Shift) 2007-2011  
TOYOTA SEQUOIA 2008-2011  
Disconnect the negative battery ter-  
minal to prevent an accidental short  
circuit.  
1
2
A
Remove (2) plastic Phillips screws  
one from each side of the trim panel  
below the cup holder then unclip and  
remove the panel. (Figure A)  
3
4
Pull the cup holder out and depress  
the (2) clips on each side to slide cup  
holder out of cup holder panel.  
(Figure B)  
Remove (4) Phillips screws from cup  
holder panel assembly then unclip  
and remove assembly. (Figure C)  
B
5
6
Unclip and remove the climate control  
assembly. (Figure D)  
Remove (4) 10 MM bolts securing the  
radio.  
7
Unclip the right side of the instrument  
panel trim and pull back then unclip  
and remove radio.  
Continue to kit assembly.  
C
D
3
 
99-8220 KIT ASSEMBLY  
DIN MOUNT RADIO PROVISION WITH POCKET  
*Note: Refer also to the instructions included with the aftermarket radio.  
A
Slide the DIN cage into the radio hous-  
ing and secure by bending the metal  
locking tabs outward. (Figure A)  
1
2
3
Slide the aftermarket radio into the cage  
until it snaps into place. (Figure B)  
Snap the pocket into the radio housing.  
(Figure C)  
Continue to final assembly.  
B
C
4
 
99-8220 KIT ASSEMBLY  
ISO MOUNT RADIO PROVISION WITH POCKET  
*Note: Refer also to the instructions included with the aftermarket radio.  
Mount the ISO Brackets to the radio  
1
using the screws supplied with the  
radio. (Figure A)  
2
3
4
Slide the radio into the radio housing  
until it snaps into place. (Figure B)  
Snap the trim plate onto the front of  
the Radio/Housing assembly. (Figure C)  
Snap the Pocket into the radio  
housing. (Figure D)  
Continue to final assembly.  
5
 
99-8220 KIT ASSEMBLY  
DOUBLE DIN RADIO PROVISION  
*Note: Refer also to the instructions included with the aftermarket radio.  
1
2
Cut and remove the center bar from  
the radio housing. (Figure A)  
Snap the Double DIN brackets to the  
inside edge of the radio housing.  
(Figure B)  
3
4
Slide the Double DIN radio into the  
bracket/radio housing assembly and  
secure the radio to the assembly using  
the screws supplied with the radio.  
(Figure C)  
Snap the Double DIN trim plate onto  
the front of the radio/housing assem-  
bly. (Figure C)  
Continue to final assembly.  
6
 
99-8220 KIT ASSEMBLY  
STACKED ISO MOUNT UNITS PROVISION  
*Note: Refer also to the instructions included with the aftermarket radio.  
1
2
Cut and remove the center bar from  
the radio housing. (Figure A)  
Snap the Double DIN brackets to the  
inside edge of the radio housing.  
(Figure B)  
3
4
Slide the stacked ISO mount units into  
the bracket/housing assembly and  
secure the units to the assembly using  
the screws supplied with the units.  
(Figure C)  
Snap the Double DIN trim plate onto  
the front of the radio/housing assem-  
bly. (Figure C)  
Continue to final assembly.  
7
 
99-8220 FINAL ASSEMBLY  
FINAL ASSEMBLY  
A
B
(A) Strip wire ends back 1/2"  
B) Twist ends together  
C) Solder  
D) Tape  
C
D
Locate the factory wiring harness in the dash. Metra recommends using the  
proper mating adapter and making connections as shown. (Isolate and individ-  
ually tape off the ends of any unused wires to prevent electrical short circuit.)  
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.  
Reassemble radio and dash assemblies in reverse order of disassembly.  
FINAL WIRING CONNECTIONS  
Make wiring connections using the EIA color code chart shown below and the instructions included with the  
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and  
individually tape off ends of any unused wires to prevent electrical short circuit.  
METRA / EIA WIRING CODE  
12V Ignition / Acc. . . . . . . . . . Red  
Right Front (+) . . . . . . . . . . . . Gray  
12V Batt / Memory. . . . . . . . . Yellow  
Ground. . . . . . . . . . . . . . . . . . Black*  
Power Antenna. . . . . . . . . . . . Blue  
Right Front (-). . . . . . . . . . . . . Gray/ Black  
Left Front (+) . . . . . . . . . . . . . White  
Left Front (-). . . . . . . . . . . . . . White / Black  
Right Rear (+) . . . . . . . . . . . . Violet  
Amp Turn-On . . . . . . . . . . . . . Blue / White  
Amp Ground. . . . . . . . . . . . . . Black / White  
Illumination . . . . . . . . . . . . . . Orange  
Dimmer . . . . . . . . . . . . . . . . . Orange / White  
Right Rear (-) . . . . . . . . . . . . . Violet / Black  
Left Rear (+) . . . . . . . . . . . . . Green  
Left Rear (-) . . . . . . . . . . . . . . Green / Black  
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.  
All colors may not be present on all leads due to manufacturer’s specifications.  
8
 
99-8220  
NOTES  
9
 
99-8220 INSTRUCTIONS  
1-800-221-0932  
REV. 11/22/10 © COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORATION INST99-8220  
 

Kuma Stoves Range OC 7 User Manual
LightSpeed Technologies Stereo Amplifier LES 600 Series User Manual
Listen Technologies Microphone DCN MICL User Manual
LST Smoke Alarm MS1R User Manual
Magic Chef Microwave Oven MCD775ST User Manual
Magic Chef Microwave Oven MCD990SC User Manual
Marantz Stereo Receiver SR8000 User Manual
M Audio Music Mixer Mulitmixer 6 User Manual
MB QUART Car Speaker RSC 210 User Manual
Micronics Car Seat W6 LI User Manual